Blog
MaintenanceIQ blog
Practical, plain-language posts for maintenance, production and quality teams, newest first.
SAP PM or a plant CMMS? An honest comparison for Indian factories
What SAP PM is good at, what a plant CMMS is good at, four questions that decide it, an illustrative example from an Indian plant, and how to split the work if you run both.
Read the postCalibration certificate: what it must contain and what auditors check
The fields a calibration certificate must carry, how to read as-found results, uncertainty and the decision rule, a review checklist to copy, an illustrative example and common mistakes.
Read the postThe investment casting process, step by step, and where maintenance decides quality
The nine steps of investment casting from wax to finished part, the machine behind each step and what it does to quality when it drifts, a PM table to copy, an illustrative example and common mistakes.
Read the postBreakdown maintenance: how to log a breakdown so it does not happen again
What to record when a machine stops, a breakdown log template to copy, five steps from restart to root cause, an illustrative foundry example and the mistakes that make the same breakdown come back.
Read the postGHG emissions calculation for factories: Scope 1, 2 and 3 basics
What Scope 1, 2 and 3 cover in a factory, the one formula behind every GHG emissions calculation, a source register to copy, an illustrative Kolhapur foundry example and the common mistakes.
Read the postPreventive vs predictive vs condition-based maintenance: which one, for which machine
How preventive, condition-based and predictive maintenance differ, four questions that pick the right one for each machine, a strategy table to copy, an illustrative Rajkot forging plant example and the common mistakes.
Read the postInstrument calibration: how often, and how to set the right interval
How to choose a first calibration interval for each instrument, review it after every calibration with the staircase method, a rule table you can copy, an illustrative Pune plant example and the mistakes that lead to audit findings.
Read the postVDA 6.3 vs IATF 16949: what is different and what maintenance must show for each
How a VDA 6.3 process audit differs from an IATF 16949 certification audit, what maintenance must show for each, an evidence table you can copy, an illustrative press shop example and the mistakes that cost points.
Read the postWhat is a good OEE score? Benchmarks and the six big losses
Where the 85% OEE benchmark comes from and why it is not your target yet, rough bands to judge your score, the six big losses with how to log each one, an illustrative CNC cell example and how to set a target your team will believe.
Read the postEHS software for factories: what it should do, and what to skip
What EHS software should do in a factory, what to leave out, a buyer's checklist you can copy, an illustrative forging plant example on man-hours and LTIFR, a two-week trial plan and common mistakes.
Read the postReliability engineering for plant teams: where to start without a reliability engineer
A practical start to reliability engineering for plants without a reliability engineer: the minimum failure record, a bad-actor list, root cause on one machine, an illustrative machining plant example, a weekly routine and common mistakes.
Read the postFSSC 22000 for maintenance teams: what the auditor will ask you to prove
Where maintenance sits in FSSC 22000, the questions an auditor asks your maintenance team, an evidence checklist you can copy, an illustrative mock audit from a biscuit plant and the mistakes that turn into findings.
Read the postDie maintenance in casting: shot counts, PM and tool life
Why die PM should run on shot counts, how dies wear out, three PM levels with a checklist you can copy, a worked example from a pressure die casting shop, and how to track tool life.
Read the postIncident investigation on the shop floor: from report to root cause
The four steps of an incident investigation, how to pick the right depth, a worked near-miss example from a press shop, a checklist you can copy, and what incident management software should do for you.
Read the postMTBF vs MTTR: formulas, a worked factory example and what good looks like
Both formulas, the counting rules that keep them honest, a worked example with a CNC, a press and a compressor, and how to tell whether your MTBF and MTTR are getting better.
Read the postPreventive maintenance: types, real examples and how to start in one week
The four types of preventive maintenance, real PM tasks for compressors, presses, CNCs, pumps and cranes, and a seven-day plan to get a PM programme running in your plant.
Read the postMES vs CMMS: which problem is your plant solving?
An MES runs production; a CMMS keeps machines able to run. How to tell which problem your plant has, where the two overlap on downtime, and which to implement first.
Read the post