Calibration

Instrument calibration: how often, and how to set the right interval

There is no single correct interval for instrument calibration. Start from the maker's recommendation, then shorten it for heavy use, harsh conditions or tight tolerances. After every calibration, look at how far the instrument had drifted, and lengthen or shorten the next interval based on that evidence rather than habit.

By Abhiram Deshpande, Business Analyst, CodiotPublished Last reviewed 7 min read

A calibration interval is the time an instrument can drift before it nears its tolerance limit A pencil sketch of a graph. Time runs left to right and error runs up. Two dashed lines mark the upper and lower tolerance limits. The instrument's error starts at zero after each calibration and drifts upward. At each calibration, marked with an orange circle, the error is checked and reset. On the left the intervals are short and the drift stays well inside the band. On the right one interval is too long and the drift line crosses the upper limit before the next calibration, marked as readings in doubt. UPPER TOLERANCE LOWER TOLERANCE 0 TIME ERROR INTERVAL TOO LONG READINGS IN DOUBT Each orange circle is a calibration: check, record, reset
Every instrument drifts. The interval is how long you let it run before you check it again. Too long, and some readings fall outside tolerance before anyone knows.

How often should instrument calibration be done?

Most plants answer this with one word: yearly. It is easy to plan and easy to explain. It is also a guess. A pressure gauge on a hydraulic press that pulses all day does not drift at the same rate as a micrometer kept in a padded box in the inspection room.

The joint guidance from ILAC and OIML on recalibration intervals, ILAC-G24 / OIML D 10, says this plainly. There is no single interval that suits all instruments. Fixed intervals that are never reviewed are not recommended, unless the interval is set by a normative document such as a standard method. The guidance expects you to choose a starting interval with care, then adjust it from the calibration results you collect.

Your quality standard asks for the same thing in different words. ISO 9001 and IATF 16949 ask that measuring equipment is calibrated or verified at specified intervals, or before use, against standards traceable to national or international standards. They leave the length of the interval to you. What an auditor checks is whether you can explain why you chose it, and whether you act when an instrument comes back out of tolerance.

So the honest answer to "how often" is: often enough that the instrument is still inside its tolerance when you next check it, and no more often than that. The rest of this post shows how to get there without a statistician.

Set the first interval: a checklist to copy

Use this when a new instrument arrives, or when you clean up an old list where everything is yearly. The factors come from the ILAC-G24 / OIML D 10 guidance, put into plant language. Fill the last column for each instrument or group of similar instruments.

Factors for a first calibration interval
FactorQuestion to askShorten the interval whenYour answer (fill in)
Maker's recommendationWhat does the manual or datasheet say?There is none, or your use is harder than the maker assumed
Required accuracyHow close is the instrument's accuracy to the tolerance you measure against?There is little margin between the two
What depends on the readingDoes a product release, a safety trip or a customer characteristic depend on it?A wrong reading would ship bad parts or hide a hazard
Extent and severity of useHow many hours a day, how many cycles?It runs every shift, or sees pulsation and shock
EnvironmentHeat, dust, vibration, moisture?It sits near a furnace, press or washer
Measured quantityDoes the quantity itself wear the sensor?Thermocouples at high temperature, gauges at the top of their range
HistoryWhat did past calibrations and repairs show?It was found out of tolerance or repaired before
Intermediate checksIs there a quick check between calibrations?There is no check at all between calibrations
Handling and transportIs it carried around, dropped, sent out by courier?It moves between stations or goes to an outside lab

New instruments deserve a shorter first interval. The guidance suggests calibrating new equipment more often at first, so you learn how it drifts before you trust a longer gap.

Review the interval after every calibration

The simplest review method in the ILAC-G24 / OIML D 10 guidance is called the staircase. After each routine calibration, you look at the as-found result, the reading before any adjustment. If the error was well inside the tolerance, you keep or extend the next interval. If it was outside, you shorten it. The guidance leaves the exact cut-off to you, and its 2007 edition gave 80 percent of the maximum permissible error as an example. You can pick a stricter cut-off, such as half the tolerance, as the rule set below does.

This only works if the lab records the as-found reading. A certificate that shows only the reading after adjustment tells you the instrument is fine today. It tells you nothing about how far it drifted, so ask your lab for both.

Two other methods from the guidance are useful on the shop floor. One counts hours of use instead of months, which suits thermocouples in a furnace or gauges that wear with each cycle. The other relies on frequent quick checks, for example a daily check of a thermometer against a reference, with a full calibration only when the check fails. Control charts and other statistical methods also exist, but they need more data and effort than most plant teams have to start with.

Here is a rule set you can copy into your calibration procedure. The steps match common recurrences: quarterly, half-yearly and yearly.

The staircase method moves an instrument's interval one step at a time Four calibrations draw in turn as bars whose length is the next interval. First: found well inside tolerance, interval stays quarterly. Second: found well inside again, it extends to half-yearly. Third: found inside, it extends to yearly. Fourth: found out of tolerance, it steps back to half-yearly and an impact review starts. Found well insideQUARTERLY Found well insideHALF-YEARLY Found insideYEARLY Out of toleranceHALF-YEARLY + impact review
The staircase method: each calibration result moves the next interval one step up, keeps it, or moves it one step down.
  1. Found within half of the tolerance, twice in a row: extend one step, for example quarterly to half-yearly.
  2. Found between half and the full tolerance: keep the interval. Note the trend.
  3. Found out of tolerance: shorten one step, start an impact review of the readings taken since the last good calibration, and record the cause.
  4. Repaired, heavily adjusted, dropped or moved to harsher duty: treat it as new and go back to the shortest step.
  5. Never extend past the maker's or the method's limit, and never extend in big jumps. A long interval that fails means a long window of readings to review.

Worked example: a machining plant in Chakan

Worked example (illustrative)

Take an auto component machining plant in Chakan, near Pune. It has 142 instruments under calibration, all on a yearly interval because that is how the list was first set up. All numbers below are illustrative.

In the last yearly round, 9 of the 60 pressure gauges on the hydraulic presses and 3 of the 12 heat treatment thermocouples came back out of tolerance. Each one meant an impact review covering up to a year of production, with the quality team going through parts records to decide what to recheck. The micrometers and the utility temperature indicators all came back well inside tolerance.

The maintenance and quality heads group the instruments by type and duty and apply the rule set above:

GroupCountLast yearly roundNew intervalCalibrations a year
Press pressure gauges609 out of toleranceQuarterly, review after two rounds240
Heat treatment thermocouples123 out of toleranceQuarterly, plus a monthly check against a reference thermocouple48
Inspection micrometers40All within a third of toleranceYearly, plus a weekly check on the setting standard40
Utility temperature indicators30All well insideYearly30
Total14212 out of tolerance358, up from 142

What the example shows (illustrative). The calibration count goes up at first, which is the price of finding out how the gauges really behave. If the press gauges then pass two quarterly rounds within half their tolerance, they step up to half-yearly and the total falls to 238. The bigger gain is the size of each impact review: a gauge that fails now puts at most three months of readings in doubt, not twelve. The utility indicators stay yearly, and the plant can later ask whether any product decision depends on them at all.

Common mistakes

  • One interval for everything. Yearly for all instruments is easy to schedule and hard to defend when a press gauge keeps failing.
  • Extending because the lab is expensive. Cost matters, but an interval should move on calibration results, not on the budget. A failed gauge after a long gap can cost more in rechecks than the calibrations you saved.
  • Reading only the after-adjustment value. Without the as-found reading you cannot tell drift from stability, so you cannot review the interval.
  • No impact review when an instrument fails. An out-of-tolerance result is a question about every reading since the last good calibration. Record what you checked and what you decided.
  • Counting from the wrong date. The interval runs from the date the calibration was done, not from the date the certificate arrived or was filed.
  • Forgetting instruments fitted to machines. Gauges, thermocouples and load cells on equipment are easy to miss because they do not sit in the calibration cupboard. List them against the machine.
  • Changing the interval without a record. If you shorten or extend an interval, write down the result that justified it. That note is what the auditor will ask for.

Frequently asked questions

How often should instruments be calibrated?

It depends on the instrument, how hard it is used, its environment and how much accuracy you need. Start from the maker's recommendation, then adjust the interval from the as-found results of each calibration.

Is a yearly calibration interval acceptable to auditors?

It can be, if you can show why it suits that instrument and you act when one comes back out of tolerance. A yearly interval applied to everything without review is hard to defend.

What is the staircase method for calibration intervals?

After each calibration you look at the as-found error. If it is well inside the tolerance you keep or extend the next interval, and if it is outside you shorten it, one step at a time.

What should I do when an instrument is found out of tolerance?

Shorten its interval, review the readings taken with it since the last good calibration, decide what needs rechecking, record the cause, and fix or replace the instrument.

Does a NABL accredited lab set my calibration interval?

No. The lab calibrates the instrument and issues the certificate. Choosing and reviewing the interval is your responsibility, based on how you use the instrument.

Fix it before it fails.

Start a free trial today, or book a demo tailored to your plant, assets and standards.

Start with one line. Extend when it works.